Tormek Rubber Work Mat RM-533

5/ 5

<p>Belgian Coticule Whetstones</p> <p>The quarrying of Belgian whetstones in the Ardennes is first mentioned in a Roman document. But the story of these natural honing stones goes further back than that. The approx. 480 million-year-old grey yellow sedimentary stones, originating from volcanic ash, are composed of very fine garnet crystals. During honing, these are released from the matrix and, in combination with water and abrasion debris, make a honing paste. The garnets only remove fine shavings from the metal and ensure a good polish. Unique combination of quick abrasive action and grain size.</p> <p>Interesting fact: To produce 1 kg of sharpening stones approx. 1500 kg of cliff must be removed. The thin yellow slices are glued to a slate base and cut to size.</p> <p>Quality of Natural Stones</p> <p>For many years, the Belgian coticule and Arkansas stones have been synonymous with high-quality whetstones. But these stones are natural products. Due to limited resources, the quality of these stones may increasingly vary. Japanese waterstones with fine grain structures are recommended as an alternative.</p> <p></p> <p>Grit 6000-8000</p> <p>Dimensions 33-39 cm²</p> <p></p>

032.402

5/ 5

<p>Compact stone for sharpening and finishing. White aluminium oxideabrasive.</p> <p>Suehiro Standard Series</p> <p>The stones from the original Suehiro series have a relatively soft bond and are thus designed for low-alloy carbon steels (Blue and White Paper Steel). The stones should be sprayed with water before use. It is not recommended to keep them in water permanently.</p> <p>Dimensions 130 x 40 x 26 mm</p> <p></p>

032.190

5/ 5

<p>For blades of any length, minimum blade width 13 mm.</p> <p>Fits Tormek models 2000-2006, 1200-1206, T-3, T-4, T-7 and T-8.</p> <p></p>

032.015

5/ 5

<p>With laser-etched degree scale for setting the correct angle of inclination on the blade.</p> <p></p>

032.265

5/ 5

<p>Arkansas stones are available in different hardnesses on the market. They are called Soft, Hard, Hard Black, Surgical, Translucent and differ in grit size. Supplied in a protective cover.</p> <p>Arkansas Oilstones</p> <p>Fine grained, extremely wear-resistant honing stones, for use with an oil lubricant. Due to their high degree of hardness, they are ideal for polishing curved cutting edges. The stones we offer have a uniform structure and are crack-free. They originate from quarries in the Ouachita Mountains in Arkansas (USA).</p> <p>Quality of Natural Stones</p> <p>For many years, the Belgian coticule and Arkansas stones have been synonymous with high-quality whetstones. But these stones are natural products. Due to limited resources, the quality of these stones may increasingly vary. Japanese waterstones with fine grain structures are recommended as an alternative.</p> <p></p> <p>Form knife-shaped</p> <p>Grit 4000-6000</p> <p>Dimensions 100 x 50 x 9.5 mm</p> <p></p>

032.205

5/ 5

<p>With two different grits. Comes with Nagura stone. For sharpening.</p> <p>Cerax by Suehiro</p> <p>Cerax is the best-known brand of the Suehiro company. The stones sold under this name have a medium-hard bond and are particularly suitable for high-alloy tool steels but also for low-alloy carbon steels. The coarse-grained alloy constituents (e.g. chromium and vanadium) in tool steels require a stone that wears slowly. The stone with the base has extra stability and is easy to store. A Nagura stone is used for cleaning and unclogging the surface of the stone and for creating a fine polishing paste. Before use, soak the stones in water for at least 10 minutes, but do not store them in water permanently. White aluminium oxideabrasive.</p> <p>Grit 1000/3000</p> <p>Dimensions 183 x 63 x 32 mm</p> <p>without base</p> <p></p>

032.156

5/ 5

<p>Specially designed for modern tool steels with a high carbon content (e.g. O1) and exotic steel alloys produced by premium tool makers. The tests that we performed on this stone series show unbeatable results, especially with HSS. The stone contains mainly extremely abrasion-resistant aluminum oxides made in Germany. It removes material quickly and has a hard bond, so it stays flat for a long time. Before use, soak the stone for at least 15 minutes. Can be permanently stored in water. Made in USA.</p> <p>Dimensions 203 x 76 x 25 mm</p> <p></p>

032.120

5/ 5

<p>Bench stone with two opposing plates with different grits. Ideal for trueing and for sharpening cutting tools. Includes two magnetic, rubber coated stone holders, cleaning block and storage pouch.</p> <p>M. Power Tools DC Diamond Stones</p> <p>Diamond Cross (DC) sharpening stones offer an excellent price/performance ratio with a high manufacturing quality. The lapping of the supporting plates and the stringent quality controls are performed at the company's headquarters in England.</p> <p>Monocrystalline* diamond particles guarantee a long service life and excellent material removal</p> <p>Uniform grit sizes and a dense diamond distribution for even grinding patterns</p> <p>Wave-shaped recesses prevent clogging due to grinding debris</p> <p>Permanently flat and warp-free thanks to specially lapped supporting plates made of steel with a stainless steel matrix</p> <p>Monocrystalline* diamond-coated sharpening devices:</p> <p>Diamond-coated sharpening devices remain permanently flat, and are especially suitable for tools with straight blades, as well as for producing flat surfaces (e.g. backs of plane and chisel blades, plane soles, scrapers). Also suitable for carbide coated cutters, tool steels, HSS and non-metal materials (glass, ceramic, etc.). We recommend moistening diamond-coated sharpening devices with water and grinding with little pressure.</p> <p>* Monocrystalline diamonds are significantly more wear resistant than the polycrystalline diamonds used to make lower quality diamond sharpening tools.</p> <p></p> <p>Grit extra-fine/coarse</p> <p>Dimensions 203 x 70 x 7 mm</p> <p></p>

032.098

5/ 5

<p>Grit 280 (No. 032.208), grit 1000 (No. 032.209) and grit 3000 (No. 032.210) in a set. White aluminium oxideabrasive.</p> <p>Suehiro</p> <p>The stones from the original Suehiro series have a relatively soft bond and are thus designed for low-alloy carbon steels (Blue and White Paper Steel). The stones should be sprayed with water before use. It is not recommended to keep them in water permanently.</p> <p></p>

032.212

5/ 5

<p>Blade length min. 60 mm.</p> <p>Fits Tormek models 2000-2006, 1200-1206, T-3, T-4, T-7 and T-8.</p> <p>Model SVM-45</p> <p>Width 45 mm</p> <p></p>

032.011

5/ 5

<p>With concave and convex surfaces, for gouges. Approx. 145 x Ø 54 x Ø 14 mm. Aluminium oxideabrasive. </p> <p>Matsunaga is one of the largest manufacturers of sharpening stones in Japan. In the West, these stones are usually known as King stones or Sun Tiger stones. The stones of the King or Sun Tiger series have a relatively soft bond, which allows the abrasives to be continually exposed during use, making the stone highly effective. These stones are particularly suitable for extremely hard, low-alloy carbon steels (White and Blue Paper Steel). Before use, soak the stones in water for at least 15 minutes. They can also be stored in water permanently. Aluminium oxideis used.</p> <p></p>

032.219

5/ 5

<p>The underside of the vegetable-tanned cowhide is softer and therefore ideal for polishing light contours or serrations on tool and knife edges.</p> <p>Leather honing strop block for honing tool, knife and razor blades. After honing on benchstones, we recommend stropping on leather for ultra-sharp edges. Can be used with or without sharpening paste.</p> <p>Dimensions 210 x 70 x 20 mm</p> <p></p>

032.145

5/ 5

<p>Weicon AT-44 is an all-round spray without silicone, which maintains and protects all tools and machines. The 3-way spray valve allows to work in any position (even overhead). Thanks to its special formula and very low friction coefficient, it combines corrosion protection, cleaning, water displacement, lubrication and conservation in a single product.</p> <p>Loosens seized screw connections, bolts, fittings and valves</p> <p>Eliminates squeaky and creaky noises on hinges, guides and bearings</p> <p>Dispels moisture from electrical cables, prevents tracking currents</p> <p>Lubricates, maintains and cleans metal surfaces and mechanical parts</p> <p></p>

032.313

5/ 5

<p>Simply mix the non-acidic formulation with water and submerge your rusty tools. It will not attack wood, wooden materials and most synthetic substances. The formula is bio-degradable, 500 ml make up a solution of ten litres. After the initial rust has been removed, the tools are protected from further corrosion.</p> <p>Content 500 ml</p> <p></p>

032.304

5/ 5

<p>Maximum precision and solid zinc cast housing</p> <p>The TORMEK T-8 Original takes precision and stability to a completely new level. The new design integrates the previously mounted sleeves for the vertical and horizontal support into the revolutionary fully cast top and frame. The enhanced stability optimises jig guidance and thus the sharpening accuracy.</p> <p>The Tormek DE-250 diamond grinding wheel with a grit size of 1200 provides a very fine grinding surface and is ideal for carving tools, knives, chisels or plane blades. Thanks to the additional grinding surface on the side, a straight bevel can be ground into the tool without hollow grinding. For sharpening on the side of the diamond grinding wheel, we recommend the Tormek Multi Base (MB-100) with the appropriate sharpening device for the respective tool.</p> <p>Sharpening wheel ""Tormek DE-250"", grit 1200, Ø 250 x 50 mm; leather honing wheel Ø 215 x 30 mm; universal support with fine adjustment (can be used horizontally or vertically). 230 V, 200 W, 90 rpm, torque 14.7 Nm, 14.8 kg.</p> <p>Includes:</p> <p>Square Edge Jig (SE-77)</p> <p>Adjustable Trueing Tool (TT-50) and Stone Grader (SP-650) for purchasing additional standard sharpening wheels (water stones)</p> <p>Anti-corrosion Concentrate, 150 ml (ACC-150)</p> <p>Pro Angle Master (WM-200)</p> <p>Honing Compound (PA-70)</p> <p>Handbook (HB-10)</p> <p>Instruction Video (DVD-1)</p> <p>Edge marker (EM-15)</p> <p>Comes with Tormek manual in German language.</p> <p>Tormek Sharpening System</p> <p>Proven for many years and constantly perfected wet working sharpening machines are the basis of the ingenious Tormek sharpening system. A range of jigs, which can be mounted on the universal support, makes the sharpening of any cutting tool easier. Tormek enables exact cutting geometry and consistent results for chisels, turning tools, knives, shears or machine tools. Also suitable for workshops and instructional settings because of safe operation - no sparks are produced and it has an overload safety clutch.</p> <p>The offered grinding wheels assure short sharpening times under all conditions in combination with the greatest possible tool protection. The offset front end can also be used for flat honing. The leather honing wheel removes burrs quickly and leaves a perfectly polished cutting edge. Robust construction with solid housing and lowerable water container.</p> <p>A summary of the advantages of Tormek sharpening machines</p> <p>Longer working life of T-8 and T-4 Original:</p> <p>Stainless steel spindle with EzyLock-System for easier stone assembling</p> <p>Solid zinc cast housing with integrated vertical and horizontal support</p> <p>Better motor insulation</p> <p></p> <p>Additional advantages of T-8 Original:</p> <p>Electrophoretic dip painted casing, zinc cast housing frame and robust ABS plastic sides for better corrosion protection</p> <p>Silent running, maintenance free motor, designed for continuous operation, 25 000 hour life</p> <p>Improved water container with screw lift for easy positioning, overspill rim, drip-off plate, magnetic swarf collector and magnetic cleaning scraper</p> <p></p>

032.325

5/ 5

<p>The Super Stone S1 is equivalent to the Super Stone S2. The different name is merely due to the smaller abrasive thickness of 10 mm. This stone series therefore is a reasonably-priced alternative for sharpening jobs where only small material removal is needed, e.g. the sharpening of razors.</p> <p>Super Stone by Naniwa</p> <p>This sharpening stone series is particularly suitable for the final polishing of knife blades. The stones provide a high polishing effect and stay flat for a long time, even though it feels as comfortable as working on soft natural stones. Those series are ideal for sharpening extremely hard low-alloy carbon steels(White and Blue Paper Steel). Before use, soak the stone for at least 10 minutes. Do not keep it in water permanently. White aluminium oxideabrasive.</p> <p>Dimensions 210 x 70 x 10 mm</p> <p></p>

032.174