HSS Chisel for Carpenters, 5-Piece Set

5/ 5

<p>"6-piece set in a leather tool roll:_ 6 / 9 / 12 / 18 / 24 / 30 mm</p> <p>Well-crafted chisels with durable double-layered blades (milled steel). Waxed handles of Japanese red oak with pre-fitted hoops.</p> <p>Blade length 58 mm</p> <p>Overall length 225 mm</p> <p>Blade thickness 5-6 mm</p> <p>Version 6-Piece Set in Leather Tool Roll</p> <p>Blade width 6 / 9 / 12 / 18 / 24 / 30 mm</p> <p> </p> <p>Set consists of the following articles:</p> <p></p> <p>Tataki Nomi, Chisel, Blade Width 6 mm</p> <p>Tataki Nomi, Chisel, Blade Width 9 mm</p> <p>Tataki Nomi, Chisel, Blade Width 12 mm</p> <p>Tataki Nomi, Chisel, Blade Width 18 mm</p> <p>Tataki Nomi, Chisel, Blade Width 24 mm</p> <p>Tataki Nomi, Chisel, Blade Width 30 mm</p> <p>Leather Tool Roll, 6 Pockets</p> <p></p>

025.212

5/ 5

<p>Made of fine-quality leather. The seams are reinforced with rivets.</p> <p>Pockets 6</p> <p>Max. tool length 270 mm</p> <p>Outer dimensions 370 x 290 mm</p> <p></p>

025.224

5/ 5

<p>Precision-made chisels with a traditional design. Forged from a chrome-vanadium steel alloy, heat-treated in an electric furnace, then ground and polished by hand. The high quality of these chisels is noticeable in their uniform hardness (approx. 60 HRC) and homogeneous fine mirror polish. The blades come pre-sharpened, ready to use, and fitted with unvarnished hornbeam handles.</p> <p>Blade length 95-105 mm</p> <p>Overall length 260-280 mm</p> <p>Blade thickness 2.5-4.5 mm</p> <p>Version Single Chisel</p> <p>Blade width 4 mm</p> <p></p>

025.172

5/ 5

025.003

5/ 5

<p>Set of Two Cherries Butt Chisels with polished blade.</p> <p>Contains 6mm / 12mm / 20mm / 26mm chisels</p>

025.304

5/ 5

<p>High-class leather protective cap made of fine cow leather which slide over the blade.</p> <p></p> <p></p>

025.245

5/ 5

<p>Made by TWO CHERRIES in Remscheid, Germany</p> <p>Skew angle 45°</p> <p>Blade polished</p> <p>Hornbeam handle</p> <p>Total length 270 mm</p> <p>Delivered as pair only</p>

025.305

5/ 5

<p>A cotton canvas tool roll protects the chisels when not in use.</p> <p>6-piece set in a cotton tool roll: 6 / 12 / 19 / 25 / 32 / 38 mm</p> <p>These chisels come in a completely Western design with a long blade of vanadium-alloyed steel for high durability (approx. 61 HRC). With a large ferrule and big handle made of Japanese red oak. The back of the blade is flat (not hollow-ground).</p> <p>Blade length 95 mm</p> <p>Overall length 255 mm</p> <p>Blade thickness 3-5 mm</p> <p>Version 6-piece set, in cotton tool roll</p> <p>Blade width 6 / 12 / 19 / 25 / 32 / 38 mm</p> <p></p>

025.158

5/ 5

<p>High-quality leather tool roll made of fine cowhide. The tools are safely secured in place by an elastic strap that prevents the tools from slipping out in any situation. The well-designed closure straps provide comfortable opening and closing, and round off the appealing design of the leather tool roll.</p> <p>Pockets 12</p> <p>Max. tool length 300 mm</p> <p>Outer dimensions 600 x 340 mm</p> <p></p>

025.223

5/ 5

<p>12-piece set in a leather tool roll: 4 / 6 / 8 / 10 / 12 / 16 / 20 / 26 / 30 / 32 / 35 / 40 mm</p> <p>Precision-made chisels with a traditional design. Forged from a chrome-vanadium steel alloy, heat-treated in an electric furnace, then ground and polished by hand. The high quality of these chisels is noticeable in their uniform hardness (approx. 60 HRC) and homogeneous fine mirror polish. The blades come pre-sharpened, ready to use, and fitted with unvarnished hornbeam handles.</p> <p>Blade length 95-105 mm</p> <p>Overall length 260-280 mm</p> <p>Blade thickness 2.5-4.5 mm</p> <p>Version 12-Piece Set in Leather Tool Roll</p> <p>Blade width 4 / 6 / 8 / 10 / 12 / 16 / 20 / 26 / 30 / 32 / 35 / 40 mm</p> <p></p>

025.186

5/ 5

<p>This set of ISI SHARP chisels is a solid basic equipment for every woodworker. The carbon steel blade (T10) is hardened to 61 - 63 HRC. The ash handles are without impact ring, so that the irons can be more comfortably guided by hand or struck with the heel of the hand. Even without an impact ring, the ash handles can withstand light to medium blows with a mallet. The handles have a colorless matte finish and are slightly flattened on two sides to prevent rolling.</p> <p></p> <p>Iron widths in the set: 6, 10, 12, 16, 20, 26 mm</p> <p>Bevel angle 25°</p> <p>Total length, depending on blade width 250 to 270 mm</p> <p>Blade length measured without tang, depending on blade width 97 to 105 mm</p> <p>Handle diameter 29 mm</p> <p>In Original wooden case</p> <p></p> <p>The Patented ISI SHARP:</p> <p>The face of a chisel must be flat in order to make precise wood joints. Most woodworkers are familiar with this fact. However, you may have experienced that it is not so easy to produce or maintain such a precise face on Western chisels.</p> <p></p> <p>The face of a Western chisel is relatively long, usually between 100 and 120 mm. When the entire length of the mirror side is honed on a flat waterstone, it bumps and lifts at the transition to the tang. At this moment, the honing stone has contact with the iron only at the cutting edge and at the tang. This means that the objective of achieving a flat mirror surface is not realized. In practice, therefore, only the part of the face close to the cutting edge is honed. However, it cannot be avoided that the face of the mirror becomes rounded over time, since there is no defined end of the grinding surface towards the tang side. Precise work is therefore only possible to a limited extent.</p> <p></p> <p>Why do Japanese chisels not have this problem? The face of Japanese chisels is short, often only 60 to 70 mm. In addition, due to single or multiple hollow grinding (Ura) of the face of the chisel, the area that has to be removed is considerably reduced. The third and decisive advantage is that the tang is angled with respect to the longitudinal axis of the face of the iron. This means that the sharpening or honing stone only touches the surface of the mirror side, which is limited on all sides. The result is a permanently flat mirror side.</p> <p></p> <p>The basic idea behind the isi sharp chisels is to transfer this advantage of Japanese chisels to Western chisels.</p> <p></p> <p>First of all, the question remains to be answered as to why Japanese chisels are not used instead of Western chisels. The answer: Many Western woodworkers find the Japanese chisels too short. Not everyone likes to get used to the angled handle.</p> <p></p> <p>The face of the isi sharp chisel chisel4 is designed as a flat surface in its part close to the cutting edge up to a length of approx. 70 mm. The novel feature is that the remaining surface is recessed by 0.5 to 0.6 mm up to the tang. This means that the surface to be ground is clearly defined on all 4 sides and reduced to the length of a Japanese chisel. This also means that the result is a permanently flat face of the chisel. This invention originates from Friedrich Kollenrott and is registered as a utility model at the German Patent Office.</p> <p></p>

025.312

5/ 5

<p>Protect your tools with these tool rolls made of indestructible »Schwingerhosen-yarn« linen. The robust »Schwingerhose« is as much admired in Switzerland as the »Lederhose« (traditional Bavarian leather trousers) in Germany. The inside is lined with grey felt and thus protects the tools from touching each other and keeps away dust and shavings.</p> <p>Pockets 8</p> <p></p>

025.252

5/ 5

<p>Max. diameter of handle 35 mm (1-3/8 inch)</p> <p>Max. recommended length of tools 300 mm (12 inch)</p> <p></p>

025.314

5/ 5

025.277

5/ 5

<p>Consisting of:</p> <p>1 chisel with straight blade, 4 mm</p> <p>1 gouge hollow medium 12 mm</p> <p>1 paring chisel 20 mm</p> <p>1 chisel with straight blade 26 mm</p> <p>This set was designed for use at construction sites, which usually lack an adequate supply of chisels. The 3/16 inch (4 mm) chisel is suitable for cutting mortises; the medium-profile gouge is useful in mounting locks and strike plates; the cranked chisel is invaluable for corner and rabbeting work - the only paring chisel which can be struck with a hammer without second thought. There is a 1 inch (26 mm) chisel for the really rough stuff. This set should be part of every construction tool box! Comes in wooden case.</p> <p></p>

025.299

5/ 5

<p>10-piece set in a wooden case: 3 / 6 / 9 / 12 / 15 / 18 / 24 / 30 / 36 / 42 mm</p> <p>Inexpensive Japanese chisels made of milled steel (double-layered, 60 HRC) in a kiri wood case. Handles made of Japanese red oak.</p> <p>Blade length 58 mm</p> <p>Overall length 225 mm</p> <p>Blade thickness 5-6 mm</p> <p>Version 10-Piece Set in Wooden Case</p> <p>Blade width 3 / 6 / 9 / 12 / 15 / 18 / 24 / 30 / 36 / 42 mm</p> <p></p>

025.200