Naniwa Combination Stone, Super Stone S1, Grit 3000/10000

5/ 5

<p>Bench stone</p> <p>A very fine grit sediment stone from the Kyoto region. Perfect for removing burr and polishing hand-forged plane blades, chisels and knife blades made of carbon steel. Ground flat on one side.</p> <p>Grit 10 000-15 000</p> <p>Dimensions 175 x 60 x 10 mm</p> <p></p>

032.361

5/ 5

<p>For short carving blades, hollow gouges and V-parting tools or small woodturning gouges A plastic cap on the pressure screw avoids pressure marks on the tools. Clamping width max. 36 mm.</p> <p></p>

032.332

5/ 5

<p>For the diamond stone dresser.</p> <p>Grinding jigs and accessories are suitable for all models (T-3, T-4, T-7 and T-8) unless otherwise noted.</p> <p></p>

032.028

5/ 5

<p>This hard-bond stone is suitable for pre-sharpening double-layered blades as well as chrome-vanadium steel and HSS.</p> <p>Fits models 1200-1206, T-3, and T-4.</p> <p>Centre hole 12 mm</p> <p>Grit 220</p> <p>Ø 200 mm</p> <p>Width 40 mm</p> <p></p>

032.029

5/ 5

<p>For straight shear blades, hedge shears or plane blades. The jaws can be finely adjusted to the respective blade thickness. The separate guide plate can also be used as a grinding table. Total clamping length 115 mm, max. blade thickness 8 mm. Suitable for sharpening machines with guide rod diameter 12 mm.</p> <p></p>

032.358

5/ 5

<p>For hollow gouges and turning tools, as well as interchangeable cutters for hollowing tools etc., up to 36 mm wide. Adjustable in cutting angle and shape. With the SVD-186 R Gouge Jig, you will get an exact replication of both the shape and edge angle on your bowl gouges and spindle gouges, so you can be sure that the tool will behave in the same predictable way on the lathe after every sharpening. Used correctly and together with your Tormek tool sharpener, there is no alternative method that can give you faster or sharper results.</p> <p>The jig can be set for various lengths of the side bevel. Mount your cutter onto the special shaft that is included with the jig, and you get a controlled sharpening.</p> <p>Fits Tormek models 2000-2006, 1200-1206, T-3, T-4, T-7 and T-8.</p> <p></p>

032.008

5/ 5

<p>Thicker and longer lasting than the cream-coloured stones, but with equally good honing properties.</p> <p>Belgian Coticule Whetstones</p> <p>The quarrying of Belgian whetstones in the Ardennes is first mentioned in a Roman document. But the story of these natural honing stones goes further back than that. The approx. 480 million-year-old grey yellow sedimentary stones, originating from volcanic ash, are composed of very fine garnet crystals. During honing, these are released from the matrix and, in combination with water and abrasion debris, make a honing paste. The garnets only remove fine shavings from the metal and ensure a good polish. Unique combination of quick abrasive action and grain size.</p> <p>Interesting fact: To produce 1 kg of sharpening stones approx. 1500 kg of cliff must be removed. The thin yellow slices are glued to a slate base and cut to size.</p> <p>Quality of Natural Stones</p> <p>For many years, the Belgian coticule and Arkansas stones have been synonymous with high-quality whetstones. But these stones are natural products. Due to limited resources, the quality of these stones may increasingly vary. Japanese waterstones with fine grain structures are recommended as an alternative.</p> <p></p> <p>Dimensions 100 x 40 x 6 mm</p> <p></p>

032.217

5/ 5

<p>Polishing emulsion with diamond particles for polishing or stropping knives and razors, as well as chisels or plane blades. Fits Jende Nanocloth acrylic strop block or leather honing strop block. To apply the emulsion, we recommend removing the pump cover, tipping the emulsion onto the strop block and spreading it evenly with a finger.</p> <p>Grit 0,5 Micron</p> <p></p>

032.280

5/ 5

<p>Shaping stone with good sharpening qualities. Green silicon carbide abrasive.</p> <p>King/Sun Tiger</p> <p>Matsunaga is one of the largest manufacturers of sharpening stones in Japan. In the West, these stones are usually known as King stones or Sun Tiger stones. The stones of the King or Sun Tiger series have a relatively soft bond, which allows the abrasives to be continually exposed during use, making the stone highly effective. These stones are ideal for extremely hard, low-alloy carbon steels (White and Blue Paper Steel). Before use, soak the stones in water for at least 15 minutes. They can also be stored in water permanently. Green silicon carbide abrasive is used for 180 grit. For all other grits aluminium oxideis used.</p> <p>Grit 220</p> <p>Dimensions 205 x 66 x 34 mm</p> <p></p>

032.188

5/ 5

<p>Arkansas stones are available in different hardnesses on the market. They are called Soft, Hard, Hard Black, Surgical and Translucent and differ in grit size.</p> <p>Arkansas Oilstones</p> <p>Fine grained, extremely wear-resistant honing stones, for use with an oil lubricant. Due to their high degree of hardness, they are ideal for polishing curved cutting edges. The stones we offer have a uniform structure and are crack-free. They originate from quarries in the Ouachita Mountains in Arkansas (USA).</p> <p>Quality of Natural Stones</p> <p>For many years, the Belgian coticule and Arkansas stones have been synonymous with high-quality whetstones. But these stones are natural products. Due to limited resources, the quality of these stones may increasingly vary. Japanese waterstones with fine grain structures are recommended as an alternative.</p> <p></p> <p>Grit 2000-3000</p> <p>Dimensions 205 x 50 x 13 mm</p> <p></p>

032.082

5/ 5

<p>For adjusting bevel angles of turning tools and chisels, independently of wheel diameter. Used in combination with jigs (SVD-186 R and SVS-50).</p> <p>Fits Tormek models 2000-2006, 1200-1206, T-3, T-4, T-7 and T-8.</p> <p></p>

032.339

5/ 5

<p>This hard-bond stone is suitable for pre-sharpening double-layered blades as well as chrome-vanadium steel and HSS.</p> <p>Fits models 2000-2006, T-7, and T-8.</p> <p>Centre hole 12 mm</p> <p>Grit 220</p> <p>Ø 250 mm</p> <p>Width 50 mm</p> <p></p>

032.030

5/ 5

<p>Compact stone for sharpening and finishing. White aluminium oxideabrasive.</p> <p>Suehiro Standard Series</p> <p>The stones from the original Suehiro series have a relatively soft bond and are thus designed for low-alloy carbon steels (Blue and White Paper Steel). The stones should be sprayed with water before use. It is not recommended to keep them in water permanently.</p> <p>Dimensions 130 x 40 x 26 mm</p> <p></p>

032.190

5/ 5

<p>Shaping stone with good sharpening qualities. Silicon carbide abrasive.</p> <p>Traditional Stone by Naniwa</p> <p>This stone series is suitable for sharpening blunt knives and tool blades. The stone has a relatively hard bond, it therefore stays flat for a longer time. It is ideal for high-alloy tool steels, but also for low-alloy carbon steels. The tool steels made of alloy components with a coarse grain structure (e.g. chromium and vanadium) require a stone that does not wear quickly. Before use, soak the stone for at least 10 minutes. Do not keep it in water permanently.</p> <p>Naniwa has changed the name and the packaging of this sharpening stone series (formerly known as DX Stone). The sharpening stone itself has not been changed.</p> <p>Grit 220</p> <p>Dimensions 210 x 70 x 20 mm</p> <p></p>

032.181

5/ 5

<p class="MsoNormal">NEW! Ultimate precision, solid zinc-cast top</p> <p class="MsoNormal">The TORMEK T-4 Original, an advanced version of the T-3 model, takes precision and stability to a new level. Both the vertical and horizontal bases for the universal support and the integrated carrying handle are made in the same zinc casting and therefore permanently joined together. The motor and main shaft are fixed to the cast top, resulting in a solid construction which significantly improves accuracy during sharpening.</p> <p class="MsoNormal">""Tormek Original"" sharpening wheel, grit 220, Ø 200 x 40 mm; leather honing wheel Ø 145 x 26 mm; solid zinc casting top with universal support with fine adjustment (horizontal and vertical settings). Impact-resistant ABS plastic housing. 230 V, 120 W, 120 rpm, 8 kg.</p> <p class="MsoNormal">Includes:</p> <p class="MsoNormal">Stone grader (SP-650)</p> <p class="MsoNormal">Pro Angle Master (WM-200)</p> <p class="MsoNormal">Honing compound (PA-70)</p> <p class="MsoNormal">Handbook (HB-10)</p> <p class="MsoNormal">Instruction video (DVD-1)</p> <p class="MsoNormal">Edge marker (EM-15)</p> <p class="MsoNormal">Voucher for free participation in a one-day workshop of your choice or a discount of €100 for a multi-day workshop</p> <p class="MsoNormal">Comes with Tormek manual in German language.</p> <p class="MsoNormal">Tormek Sharpening System</p> <p class="MsoNormal">Proven for many years and constantly perfected wet working sharpening machines are the basis of the ingenious Tormek sharpening system. A range of jigs, which can be mounted on the universal support, makes the sharpening of any cutting tool easier. Tormek enables exact cutting geometry and consistent results for chisels, turning tools, knives, shears or machine tools. Also suitable for workshops and instructional settings because of safe operation - no sparks are produced and it has an overload safety clutch.</p> <p class="MsoNormal">The offered grinding wheels assure short sharpening times under all conditions in combination with the greatest possible tool protection. The offset front end can also be used for flat honing. The leather honing wheel removes burrs quickly and leaves a perfectly polished cutting edge. Robust construction with solid housing and lowerable water container.</p> <p class="MsoNormal">A summary of the advantages of Tormek sharpening machines</p> <p class="MsoNormal">Longer working life of T-8 and T-4 Original:</p> <p class="MsoNormal">Stainless steel spindle with EzyLock-System for easier stone assembling</p> <p class="MsoNormal">Solid zinc cast housing with integrated vertical and horizontal support</p> <p class="MsoNormal">Better motor insulation</p> <p class="MsoNormal"></p> <p class="MsoNormal">Additional advantages of T-8 Original:</p> <p class="MsoNormal">Electrophoretic dip painted casing, zinc cast housing frame and robust ABS plastic sides for better corrosion protection</p> <p class="MsoNormal">Silent running, maintenance free motor, designed for continuous operation, 25 000 hour life</p> <p class="MsoNormal">Improved water container with screw lift for easy positioning, overspill rim, drip-off plate, magnetic swarf collector and magnetic cleaning scraper</p> <p></p> <p></p>

032.007

5/ 5

<p>Developed primarily for modern tool steels with high carbon content (e.g. O1) and exotic steel alloys used by premium tool manufacturers. In our tests, the stone series achieved unrivalled results especially with HSS. The stones consist mainly of extremely abrasion-resistant aluminium oxides of German production. The stone provides very fast material removal and has a hard bond; it therefore stays flat for a long time. The stones should be soaked in water for at least 15 minutes before use and can be stored in water permanently. Made in the USA.</p> <p>Dimensions 203 x 76 x 25 mm</p> <p></p>

032.140